TECHTONGDA Automatic Wire Stripping Machine 110V - Copper Cable Stripper with 11 Channels & 10 Blades (0.06-1.5 Inch) for Scrap Metal Recycling | Perfect for Electricians, DIY Projects & Copper Wire Processing

This Electric copper wire stripping machine,is a machine which can be used for stripping your wasted copper wires and cables,the wire stripper diameter range 1.5-38mm,such as telephone wire ,car wire and the general wasted wires and cables.(recycling the wasted wires,you also can use the copper wire granulator machines,will be more big capacity ,more nice performance) This electric wire stripper adopts a power motor, which is 370W. The high quality motor has the advantages of low loss, high efficiency, low temperature rise, high reliability and long service life. This wire stripper has high working efficiency, the Strippingmachine is equipped with multiple holes, which can process multiple waste cables at the same time, it can save a lot of labor, and the effect is better. Reduction box for decrease the operating speed of axis to avoid the dangerous suitation. Frame dual blades principal, can process different diameter cable, easy to operate and durable. Specifiction Voltage: 110VPower370WWire Stripping range: Φ0.059"~1.49"(Φ1.5mm~ 38mm)Item Included: A set of 110V Wire Stripper Machine(153082) Feature This machine is easily to use, portable,energy saving and good looks,just like the normal stripper machine usage.This model are easy to operate, convenient to carry, energy saving, for single copper wire(hard wires) can be rolled or blades stripping, other cables(soft wires) can be easily stripped. If the cables/wires were blocked in the axises, please check below points If the springs on the press wheels are too tight, loose them. There are too much oil on the cables/wires, please wipe it. Comparing the cables/wires’ diameters with the feeding holes on the machine, feeding the cables/wires one piece at one time. Before feeding the cables/wires, please cut off the head of the cables/wires, to avoid gaps caused to the blades. On the output side, if the cuts on the cables/wires are too deep, please check below points Please adjust the handles on the input side, screw down or loose them. (M12 handles)Check whether the cables/wires on the right position as you feeding them.Make sure the blades are sharp, if not, polish them with the oil stone. Notice On the output side, if see the plastic (PVC) has been stripped, but the copper wires can not been disgorged, please check below 4 points: Polish the axis of the upside with the oil stone.Check whether the springs are loose, if yes, screw down to make them tighten.The diameter of the cables/wires are too small, please adjust the space between the two axises to 0.3-0.6mm.If the cables/wires you want to strip are hot, also can not get the copper wires stripped out. If see the blades tilted : Check whether the center adjuster was loosed.Centering adjustment and adjust the screws of two sides of it. Make sure the cables/wires’ diameter are similar with the feeding holes, large cables/wires in large feeding holes, small cables/wires in small feeding holes, flat cables/wires in flat feeding holes. Notice On the output side, if see the plastic (PVC) has been stripped, but the copper wires can not been disgorged, please check below 4 points: Polish the axis of the upside with the oil stone.Check whether the springs are loose, if yes, screw down to make them tighten.The diameter of the cables/wires are too small, please adjust the space between the two axises to 0.3-0.6mm.If the cables/wires you want to strip are hot, also can not get the copper wires stripped out. If see the blades tilted : Check whether the center adjuster was loosed.Centering adjustment and adjust the screws of two sides of it. Make sure the cables/wires’ diameter are similar with the feeding holes, large cables/wires in large feeding holes, small cables/wires in small feeding holes, flat cables/wires in flat feeding holes.